Driver sr needs updating please use bus type who is gretchen dating slade

Driver sr needs updating please use bus type

For most of the country, the off-peak hours are between 9am to 3pm and from pm to the end of service on weekdays, and any time on weekends and public holidays.

upgrading to a new Open Wrt version you can upgrade using the mtd command line tool. Starting program at 0x80014230 Linux version 2.6.30 ([email protected]) (gcc version 4.4.2 (Buildroot 2010.02-git) ) #1 Wed May 21 CST 2014 Parallel flash device: name AM29DL800B, id 0x22cb size 8192KB 96368MT-1341N1 prom init CPU revision is: 0002a031 (Broadcom4350) Determined physical RAM map: memory: 03ece000 @ 00000000 (usable) Zone PFN ranges: DMA 0x00000000 - 0x00003ece On node 0 totalpages: 16078 free_area_init_node: node 0, pgdat 8038a7e0, node_mem_map 81000000 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4064 pages, LIFO batch:0 Normal zone: 94 pages used for memmap Normal zone: 11888 pages, LIFO batch:1 Built 1 zonelists in Zone order, mobility grouping on.

Смотрел исходник drivers/net/sis190.c, но понял мало, а изучать железячные стандарты времени нет. Перерегистрировался с реальным MAC’ом, и соединение появилось. (Правда, чтоб в Интернет ходить, пришлось у VPN-соединения (PPTP) снизить MTU с 1460 до 1456 — я фигею с этой жизни…) Всё же интересно, почему не удавалось соединиться под локальным MAC.

В Интернете пишут, что в Линуксе с этим проблем нет.

[ 40.972360] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 41.076007] eth0: mii ext = 0000. [ 41.092054] eth0: link on 100 Mbps Full Duplex mode. mii-diag.c:v2.11 3/21/2005 Donald Becker ([email protected]) the new SIOCGMIIPHY value on PHY 1 (BMCR 0×3100). Able to perform Auto-negotiation, negotiation complete. Your link partner advertised 45e1: Flow-control 100base Tx-FD 100base Tx 10base T-FD 10base T, w/ 802.3X flow control. libmii.c:v2.11 2/28/2005 Donald Becker ([email protected]) PHY #1 transceiver registers: 3100 786d 0000 8201 01e1 45e1 0001 0000 0000 0000 0000 0000 0000 0000 0000 0000 000c 01c0 0000 0000 0000 0000 0000 0000 0000 00f9 0000 0000 0000 0000 0000 0000. Able to perform Auto-negotiation, negotiation complete. [ 7.064025] 00.0: Using transceiver at address 1 as default.

[ 51.616013] eth0: no IPv6 routers present Пусто: $ sudo /sbin/iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination Вроде были баги в драйвере sis190, например: Basic mode control register 0×3100: Auto-negotiation enabled. [ 7.096307] 00.0: Si S 191 PCI Gigabit Ethernet adapter at f80a4c00 (IRQ: 19), :7f:71:7b [ 7.096377] eth0: GMII mode. Offload parameters for eth0: Cannot get device rx csum settings: Operation not supported Cannot get device flags: Operation not supported rx-checksumming: off tx-checksumming: off scatter-gather: off tcp segmentation offload: off udp fragmentation offload: off generic segmentation offload: off large receive offload: off Я заметил.

driver sr needs updating please use bus type-25driver sr needs updating please use bus type-49driver sr needs updating please use bus type-35

Просьба ссылок на английские обсуждения не давать, вроде Если можно объясните из-за чего возникает.

Join our conversation (36 Comments).
Click Here To Leave Your Comment Driver sr needs updating please use bus type.

Comments:

Leave a Reply

Your email address will not be published. Required fields are marked *